Use only a trolley or stand recommended by the manufacturer or sold with the monitor. This will alleviate the growing health concerns. Do not place the monitor near or over a radiator or heat register. Fig 4 Fig 3 Fig 4 29 Disassemble the shieldRemove two screws to release the shield. Remove four screws to release power board.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. Please, do not make a copy of the downloaded manual and do not offer to sell it, just use personally to repair defective appliance! Az inverter nem megy, dugtam rá próba lámpákat, általában eddigi inverter hibáimnál valamennyire mindig felvillan a lámpa, de most meg sem nyekken egyik sem. You might be using these following steps to examine what wrong with your monitor. I hope this helps, if so please rate my solution. Do not place the monitor on a bed, sofa, rug, or similar surface. Jól látom, vagy tévedek, és van más megoldás? Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltages and other hazards.
Reconnect P103 and P104 in tightly. Remove connector wire with main board and power board. Is the power key pressed? You might be using these following steps to examine what wrong with your monitor. If you cannot see anything on the screen, there'll be some problems with inverter board. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours. Electronics Engineering Resources, Articles, Forums, Tear Down Videos and Technical Electronics How-To's Mar 18 2019, 4:00 am : Mar 18 2019, 4:00 am : Mar 16 2019, 10:04 am : Mar 16 2019, 9:56 am : Mar 16 2019, 9:51 am : Mar 15 2019, 7:56 am : Mar 14 2019, 1:42 pm : Mar 14 2019, 9:08 am : Mar 14 2019, 9:02 am : Mar 14 2019, 8:43 am :.
The Inverter board will drive the backlight of panel. Check +3V3 supplied on I309 pin8. What is the screen resolution for acer al1716 monitor? Connect the video cable from the monitor to the video card. The used lamp current is the lamp typical current. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.
As a safety precaution, always unplug the monitor before cleaning it. If you open your monitor and see blown capacitors that look like the pictures on our site then replace the bad ones and you should be back going. Power Code Attach the monitor to the power cord which should then be inserted into a properly grounded electric socket. Support ModesThere will be 20 total support modes to accommodate the above mode and other video modes within the frequency range of the monitor. This item may or may not be in original packaging.
Remove five screws to release back cover and front bezel. The monitor is equipped with a three-pronged grounded plug, a plug with a third grounding pin. Remove connector wire with main board and panel. Connect the video cable from the monitor to the video card. The display is restored by pressing a key on the keyboard, or clicking the mouse. Intel is a registered trademark of Intel Corporation.
Pull the 4 hooks on bottom side of the base and hold. This plug will fit only into a grounded power outlet as a safety feature. If you cannot see anything on the screen, there'll be some problems with inverter board. Item Picture Description Part No. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. List item the first 2. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely.
When the Hsync Frequency, Vsync Frequency or Resolution is out of The monitor support range will show this message. Unplug the unit during a lightning storm or when it will not be used for long periods of time. R323 and C327 may be short. Before, the backlight was turning off almost immediately, now it glows for 1-2 seconds and then turns off. Exploded Diagram continued Go to cover page 3.