Sabre lawn tractor manual. Specifications 2019-02-20

Sabre lawn tractor manual Rating: 4,7/10 1046 reviews

John Deere Sabre

sabre lawn tractor manual

Put lift lever in lowest position, bringing deck down onto blocks. Tighten cap screws to specification. Position the deck so the rear draft arms A are between the guide rods B and the lift arms C. Clutch Cross Shaft and Bellcrank F. Park tractor on level surface and remove battery. Connect and adjust throttle cable C to obtain full throttle and choke when lever is full forward, and 7. Reason: Check both sides of connectors closely as To check for opens, loose terminal wire crimps, poor disconnecting and connecting may temporarily connections, or corrosion in the ground circuit.

Next

John Deere Sabre

sabre lawn tractor manual

Improperly oriented belt keepers can result in thrown belts, premature belt wear or breakage. · Always wear gloves when handling mower blades or working near blades. Carefully separate transaxle housing into upper and G brake puck minimum. Discount will be automatically applied during check-out. Hose Clamps 6 used 12. Fasten fuel tank to dash panel with six screws. If scratched or deformed, replace upper case half.

Next

John Deere Sabre

sabre lawn tractor manual

The shift lever turns the transaxle shifter shaft. Secure with spring locking pins. Install thin bearing thrust washer G first, ball bearing H , and thick bearing thrust washer I on top mates with pump pistons into swashplate J. Maximum allowable resistance in the circuit is 0. Do not expose to flame or negative - cable.

Next

SABRE 1338 GEAR TECHNICAL MANUAL Pdf Download.

sabre lawn tractor manual

Measure distance from bracket A to washer B on tension rod C. Cylinders One Oil Filter None Air Filter Paper with Foam Transmission Gear Transaxle Transaxle Manufacturer Dana 4360 Travel Speeds 5 Gear Speed Range 1st 2. · Always wear gloves while working on blades. Cannot be applied to previous purchases and cannot be redeemed for cash. Install assembly in reverse order, making sure pinion gear and sector gear alignment marks are aligned as steering pinion shaft F is installed. This will ensure shift lever will remain stationary wherever operator lets go of lever anywhere in shift quadrant.

Next

SABRE 1338 GEAR TECHNICAL MANUAL Pdf Download.

sabre lawn tractor manual

· Always wear safety eye protection when grinding. The replacement part does not look like the original. This factory John Deere Service Manual Download will give you complete step-by-step information on repair, servicing, and preventative maintenance for your John Deere. Do not remove tensioning spring when adjusting mower belt tension. The location of tractor identification number and component serial numbers are shown below.

Next

Sabre Lawn Mower Manuals

sabre lawn tractor manual

Remove link arm from steering yoke by rotating link transaxle drive sheave. Spur gear 14 teeth 47. Check shift linkage bellcrank spring tension by measuring spring length distance E between flanged nut and top anchor washer and adjust to specification. Done so for the last 12 years. Carefully remove axle shaft assembly components from ring gear G. These John Deere Manuals make it easy for any skill level with these very easy to follow, step-by-step instructions! See Parking Safely in Safety Section. Remove belt from engine drive sheave and belt guides: a.

Next

SABRE 1338 GEAR TECHNICAL MANUAL Pdf Download.

sabre lawn tractor manual

Safely raise and block tractor to gain easy access to underside of frame. Drive chain drive sprocket 9 teeth 3. See Parking Safely in Safety Section. Side Specifications: Brake Components Wear Tolerances— K brake puck minimum. Transaxle Drive Input Sheave C.

Next

John Deere Sabre 1948GV Lawn and Garden Tractor Service Manual Download

sabre lawn tractor manual

Remove shifter shaft rubber boot E. These models were never that popular with consumers as most were confused as to exactly who made these tractors. Place mower deck in lowest setting. Function: The transaxle transmits power from the engine to the drive axles and rear wheels, and provides gear selection of five forward speeds, one reverse, and neutral. Transaxle Drive Sheave Function: The belt traction drive transfers power from the engine drive sheave to rotate without transferring any power.

Next